Call us: +61 2 9838 8899
FAX: +61 2 9838 8818



24-Port 10/100Mbps + 2 Gigabit TP/SFP Managed PoE Switch 


  • Overview
  • Cost-effective 24-port PoE Switch for SMB PoE Networking
    PLANET FGSW-2620PVM PoE Switch features 802.3af Power over Ethernet (PoE) function, which optimizes the installation and safe power management of network devices such as wireless access points (AP), Voice over IP (VoIP) phones and IP surveillance cameras. 802.3af PoE capabilities reduce installation costs of add-in network productivity devices. It frees the wireless AP deployment from restrictions of power outlet locations. With PoE features, power and data switching are integrated into one unit and delivered over a single cable, eliminating costs for additional AC wiring and reducing installation time. It provides a compact, affordable, safe and reliable power solution for small to medium enterprises.

    Power over Ethernet, Easy Cabling Installation
    The PoE in-line power following the standard IEEE 802.3af makes the FGSW-2620PVM able to power on 24 PoE compliant devices at the distance up to 100 meters through the 4-pair Cat 5/5e UTP wire. With data and power over Ethernet, the FGSW-2620PVM can reduce cable deployment and eliminate the need for electrical outlets on the wall, ceiling or any unreachable place. A wire carries both data and power, thus lowering the installation costs, simplifying the installation effort and eliminating the need for electricians or extension cords. The key feature of the deployment is energy saving. With more efficient switching power supply, the efficiency of the FGSW-2620PVM would be much better than four linear power adapters in the long run.

    Centralized Power Distribution with Remote Management
    The remote PoE management functions of the FGSW-2620PVM make it easy to survey and control the PoE power provision to the devices and ensure interoperability with equipment from other vendors. Via Web interface, SNMP trap and SNMP monitoring, the manager can get the PoE devices status and alert immediately. The over-temperature detection of the PoE switch offers a safe and stable PoE operation by limiting the output power according to detected temperature to prevent destructive breakdown caused by un-expected overheating.

    High Performance Wire-Speed Switching
    PLANET FGSW-2620PVM offers 24 10/100Mbps Fast Ethernet ports and 2 Gigabit TP/SFP combo ports. The two Gigabit TP/SFP combo ports can be either 1000Base-T for 10/100/1000Mbps or 1000Base-SX/LX through SFP (Small Factor Pluggable) interface. PLANET FGSW-2620PVM boasts a high performance switch architecture that is capable of providing non-blocking switch fabric and wire-speed throughput as high as 8.8Gbps. Its two built-in GbE uplink ports also offer incredible extensibility, flexibility and connectivity to the core switch or servers.

    Efficient Management
    To further expand the current network, PLANET FGSW-2620PVM provides console and telnet command line interface, and advanced Web and SNMP management interfaces to fill this kind of demand. With its built-in Web-based management, the FGSW-2620PVM offers an easy-to-use, platform-independent management and configuration facility. The FGSW-2620PVM supports standard Simple Network Management Protocol (SNMP) and can be monitored via any standard-based management software. For text-based management, the FGSW-2620PVM can also be accessed via Telnet and the console port. Moreover, the FGSW-2620PVM offers secure remote management by supporting Secure Socket Layer (SSL) connection which encrypts the packet content at each session.

    Robust Layer 2 Features
    For efficient management, via Web interface, the FGSW-2620PVM can be programmed for basic switch management functions such as port speed configuration, Port link aggregation, IEEE 802.1Q VLAN and Q-in-Q VLAN, Port Mirroring, Rapid Spanning Tree and ACL security. Additionally, the firmware includes advanced features such as IGMP snooping, QoS (Quality of Service), broadcast storm and bandwidth control, to enhance bandwidth utilization.

    Advanced Security and Quality of Service
    PLANET FGSW-2620PVM offers comprehensive Layer 2, Layer 3 and Layer 4 Access Control List (ACL) to filter out unwanted traffic. Its protection mechanism comprises RADIUS and Port-based 802.1X user and device authentication. Moreover, the switch provides MAC filter, Static MAC, IP/MAC binding and Port Security for enforcing security policies to the edge. The administrators can now construct highly secured corporate networks with considerably less time and effort than before.

    To ensure IP voice and video communication get the quality of service needed, the FGSW-2620PVM classifies traffic and prioritizes Layer 2 802.1p or Layer 3 IP DSCP traffic into four hardware queues that support strict or Weighted Round Robin (WRR) queuing algorithms. It also empowers the SMB IP office to take full advantages of the limited network resources and guarantees the best performance in VoIP and video conferencing transmission.

  • Applications
  • PoE IP Telephony Office

    With the expansion of business office, the additional telephones required could be installed in less cost via the implementation of PoE IP Telephony system than that of the traditional circuit wiring telephony system. PLANET FGSW-2620PVM PoE Managed Switch helps SMBs to create an integrated data, voice, and powered network. PLANET 802.3af compliant IP phones can be installed without the need of additional power cables because the power can be provided from the standard Ethernet cable connecting to the FGSW-2620PVM. PoE IP phones and analog Telephony adapter work perfectly with the FGSW-2620PVM which injects power through the Ethernet cables and the IP DSCP priority of QoS feature improves the voice communicating. With the FGSW-2620PVM, IP Telephony deployment becomes more reliable and cost effective, which helps SMBs save tremendous cost when upgrading from the traditional telephony to IP Telephony communications infrastructure.

    Department / Workgroup PoE Switch

    Providing up to 24 PoE, in-line power interface, the FGSW-2620PVM Managed PoE Switch can easily build a power centrally-controlled IP phone system, IP camera system, or wireless AP group for the enterprises. For instance, 24 cameras or APs can be easily installed in the company for surveillance demands or building a wireless roaming environment in the office. Without the power-socket limitation, the PoE Switch makes the installation of cameras or WLAN AP easier and more efficient.

    Factory / Warehouse Applications

    While video surveillance system becomes more and more important for visible security in the factory or warehouse, the IP cameras with PoE function would be a lot helpful for the surveillance deployment when the power outlet can not be easily found in the ceiling or in the outdoors. For example, in the factory operation or in the warehouse storage security, the PoE IP cameras can be installed anywhere when needed regardless of the restrictions of power outlet location. With the PoE switch as the central control manager and offering remote power monitoring via Web interface or SNMP trap and SNMP monitoring, the manager can get the PoE devices status and alert immediately. The PoE IP cameras could also be controlled remotely, which increases the administrator management efficiency and improves the productivity.

  • Key Features
  • Physical Port
    • 24-Port 10/100Mbps Fast Ethernet ports with PoE Injector
    • 2 10/100/1000Mbps TP and SFP shared combo interfaces
    • RS-232 male DB9 console interface for switch basic management and setup
    • Reset button for system management

    Power over Ethernet
    • Complies with IEEE 802.3af Power over Ethernet End-span PSE
    • Up to 24 IEEE 802.3af devices powered
    • PoE Power up to 15.4 watts for each PoE port
    • Auto detects powered device (PD)
    • Circuit protection prevents power interference between ports
    • Remote power feeding up to 100m
    • PoE Management
     –Total PoE power budget control
     –Per port PoE function enable/disable
     –PoE port Power feeding priority
     –Per PoE port power limit
     –PD classification detection

    Layer 2 Features
    • Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z Gigabit
     Ethernet standard
    • Supports auto-negotiation and full-duplex / half-duplex modes for all 10Base-T / 100Base-TX and 1000Base-T ports
    • Auto-MDI/MDI-X detection for each RJ-45 port
    • Prevents packet loss Flow Control:
     –IEEE 802.3x pause frame flow control for full-duplex mode
     –Back-Pressure Flow Control in Half-Duplex mode
    • High performance of Store-and-Forward architecture, runt/CRC filtering eliminate erroneous packets to optimize the network bandwidth
    • Broadcast / Multicast / Unicast storm control
    • 8K MAC address table, automatic source address learning and ageing
    • VLANs
     –IEEE 802.1Q Tag-based VLAN
     –Port-based VLAN
     –Q-in-Q tunneling
     –Up to 255 VLANs groups, out of 4041 VLAN IDs
    • Link Aggregation
     –up to 13 trunk groups
     –up to 8 ports per trunk group with 1.6Gbps bandwidth (full duplex mode)
     –IEEE 802.3ad LACP (Link Aggregation Control Protocol)
     –Cisco ether-channel (static trunk)
    • Spanning Tree Protocol
     –STP, IEEE 802.1D (Classic Spanning Tree Protocol)
     –RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
    • Port mirroring to monitor the incoming or outgoing traffic on a particular port

    Quality of Service
    • 4 priority queues on all switch ports
    • Traffic classification:
     –IEEE 802.1p CoS
     –IP TOS / DSCP to 802.1p priority mapping
     –Port-Based priority
    • Strict priority and Weighted Round Robin (WRR) CoS policies
    • QoS and In / Out bandwidth control on each port

    • IGMP Snooping v1 and v2
    • IGMP Snooping v2 fast leave
    • Querier mode support

    • IEEE 802.1x Port-based network access control protocol
    • RADIUS users access authentication
    • L2 / L3 / L4 Access Control List (ACL)
    • MAC Filtering and Source IP-MAC / Port-Binding
    • Port Security for Source MAC address entries filtering

    • Switch Management Interface
     –Console / Telnet Command Line Interface
     –Web switch management
     –SNMP v1, v2c switch management
     –SSL switch management
    • DHCP client for IP address assignment
    • Built-in Trivial File Transfer Protocol (TFTP) client
    • Firmware upgrade via TFTP or HTTP
    • Configuration upload / download via TFTP or HTTP
    • Four RMON groups 1, 2, 3, 9 (history, statistics, alarms, and events)
    • SNMP trap for interface Link Up and Link Down notification
    • Ping function

  • Specifications
  • Hardware Specifications
    10/100Mbps Copper Ports 24 10/ 100Base-TX RJ-45 auto-MDI/MDI-X ports
    1000Mbps Copper Ports 2 10/100/1000Mbps RJ-45 auto-MDI/MDI-X ports
    SFP/mini-GBIC Slots 2 1000Base-SX/LX, shared with Port-25~Port-26
    Switch Architecture Store-and-Forward
    Switch Fabric 8.8Gbps / non-blocking
    Switch Throughput 6.547Mpps @64Bytes
    Address Table 8K entries
    Share Data Buffer 512Kbytes
    Maximum Frame Size 9K Bytes
    Flow Control Back pressure for half-duplex

    IEEE 802.3x pause frame for full-duplex

    LED Power, Fan Alarm

    Link/Activity (Green)

    PoE In-Use (Amber)

    1000 LNK / ACT(Green)

    10/100 LNK / ACT(Green)

    Reset Button < 5 sec: System reboot > 5 sec: Factory Default
    Dimensions (W x D x H) 440 x 265 x 44 mm, 1U height
    Weight 3.6kg
    Power Requirements 100~240V AC, 50-60 Hz
    Power Consumption / Dissipation 210 watts maximum / 717 BTU/hr maximum
    Power over Ethernet
    PoE Standard IEEE 802.3af Power over Ethernet / PSE
    PoE Power Supply Type End-span
    PoE Power Output Per Port 48V DC, 350mA . Max. 15.4 watts
    Power Pin Assignment 1/2(+), 3/6(-)
    PoE Power Budget 190 watts
    Max. number of Class 2 PD 24
    Max. number of Class 3 PD 12
    Layer 2 Functions
    Management Interface Console, Telnet, Web Browser, SSL, SNMPv1, v2c
    Port Configuration Port disable/enable


    10/100/1000Mbps full and half duplex mode selection

    Flow Control disable / enable

    Bandwidth Control Ingress / Egress Rate Control

    Allow to configure per 128Kbps

    VLAN IEEE 802.1Q Tag-based VLAN

    Port-based VLAN

    Q-in-Q tunneling

    Up to 255 VLANs groups, out of 4041 VLAN IDs

    Link Aggregation Static Port Trunk

    IEEE 802.3ad LACP (Link Aggregation Control Protocol)

    Supports 13 groups of 8-Port trunk support

    Quality of Service Traffic classification based on :

    -Port priority

    -802.1p priority

    -DSCP/TOS field in IP Packet

    IGMP Snooping IGMP (v1/v2) Snooping, up to 256 multicast Groups

    IGMP Querier support

    Port Mirror RX / TX / Both

    1-to-1 mirroring

    Security IEEE 802.1x Port-based Network access control

    Port Security

    Static MAC

    MAC Filtering

    MAC / IP Binding

    Access Control List IP-based Layer 3 / Layer 4 ACL

    Up to 220 ACL rule entries


    RFC-2863 Interface MIB

    RFC-2665 EtherLike MIB

    RFC-1493 Bridge MIB

    RFC-2819 RMON MIB (Group 1, 2, 3,9)


    Standards Conformance
    Regulation Compliance FCC Part 15 Class A, CE
    Standards Compliance IEEE 802.3: 10Base-T

    IEEE 802.3u: 100Base-TX

    IEEE 802.3z: 1000Base- SX/LX

    IEEE 802.3ab: 1000Base-T

    IEEE 802.3x: Flow Control

    IEEE 802.3ad: Port trunk with LACP

    IEEE 802.1D: Spanning tree protocol

    IEEE 802.1w: Rapid spanning tree protocol

    IEEE 802.1p: Class of service

    IEEE 802.1Q: VLAN Tagging

    IEEE 802.1x: Port Authentication Network Control

    IEEE 802.3af: Power over Ethernet

    Temperature: 0 ~ 50 degrees C
    Relative Humidity: 20 ~ 95%
    Temperature: -10 ~ 70 degrees C
    Relative Humidity: 20 ~ 95% (non-condensing)
  • Downloads

  • Datasheet

    Date Version Description Download
    2013-04-19 1.0 FGSW-2620PVM


    Date Version Description Download
    2010-03-05 1.20 Bug Fixed-
    1. Fix Switch panel location in Web UI
    2. Fix Power Allocation could not display correct power consumption of the support POE power class PD device.

    Quick Guide

    Date Version Description Download
    2009-09-14 1.1 Quick Install Guide
    2009-05-20 1.0 Quick Install Guide

    User’s Manual

    Date Version Description Download
    2012-04-13 2.4 Function Added: Port description, Users configuration, Configuration Backup without IP(Web only), PoE limit-mode…
    2010-04-09 2.3 Add new model’s content.
    2009-09-14 1.2 User’s Manual
    2009-05-20 1.1 User’s Manual
    2009-05-20 1.0 User’s Manual

    EC Declaration

    Date Version Description Download
    2009-10-30 1.0 EC Declaration
    Ordering Information
    FGSW-2620PVM 24-Port 10/100Mbps +2 Gigabit TP/SFP Combo Managed PoE Switch